Dartboard Lighting

Tell a Friend

"A good lighting system should effectively light the board evenly and eliminate any shadow a dart could cast by secondary lighting.’ – David King Darts501.com"  

Circumluminator - The Dartboard Light

Circumluminator - The Dartboard Light

To this date I have only seen one commercial lighting solution especially  design to light a dart board that eliminates shadow. The lighting system is called ‘The Circumluminator Dartboard Light. Design in the United States the Circumluminator does exactly what any dart player would like a dart board light to do, eliminate shadow.

I first reviewed The Circumluminator in 2005, one of the first 25 to roll off the production line.My opinion of the light at that time was mixed. The light did exactly what it said it would do i.e. eliminate shadow. However I was critical about the overall quality and hence to say i gave my feedback to Scott Harrison the inventor of the Circumluminator he has since taken on board my my views and revise the product considerably. Here are the new specification supplied by Scott. To me it looks like a new product, refined in every aspect:

"The lamp housing is now injection molded of Lexan polycarbonate, and is 5mm thick throughout. The slotted keyway for mounting the dartboard is substantially stronger and the plastic springs extending from the back of the lamp housing now hold the dartboard securely, preventing it from accidental rotation during play.

The custom graphics displayed backlit on the radial face of The Circumluminator are now printed on heavyweight, glossy photo paper of much higher quality than the lightweight matte finish paper I used initially.

Graphics are now standard design on the annular outside surface of The Circumluminator to prevent bright light from escaping from the periphery of The Circumluminator.

New neon lamp with one made of a special new glass that emits a warm white which is twice as bright as the early model

The 240 VAC neon transformer is now replaced with a low-voltage 12 VDC one which fits better in the lamp housing and makes it possible to use a switching 100 - 240 VDC wall plug adapter with changeable blades for worldwide distribution. This transformer and power supply change achieved another doubling of the brightness of the lamp adding up to four times the dartboard illumination of the earlier model

The Foam ring which serves to fill the void between the Dartboard and the lamp housing is now die cut quarter circles which I glue securely together with a protruding handle glued to one of the joints for ease of removal. "


Scott Harrison
 

All the criticisms I initially wrote about the early Circumluminator seemed to have been addressed and the new graphic Scott has sent me seems to demonstrates the new Circumluminator is the dartboard light to have. (Picture Circumluminator Tynte Hotel , South Wales)

As far as innovation goes we don’t tend to see many radical dart improvements however this is one. For more information where you can see buy and see a Circumluminator please visit their website.

Ok, the Circumluminator is the only dartboard light designed for purpose. So what else is being used.


A basic set up is a single spot light either fixed to the wall, ceiling of dart stand. This lights the board and is set up is most common in clubs, pubs and home setups. If you opt for this try using a high wattage bulb fitting and bulb 100w. Example of this can been seen to the left.

 

 


Tournament setups


Tournament dart board lighting is pretty standard but could be better, here is an example. The illustration shows the distribution of light, the bulb is focused on the twenty segment to the determent of the rest of the board. This is normal practice but it clearly shows the limitations of using just one bulb to light the board.

Another way to help reduce shadow, although, this will not entirely eliminate shadow is to have a few spots lights focused of the board from either side I.e. left, right and middle. This can easily be achieved by using on of the commercially available strip spot light set-ups as below.

 

The cross lighting reduces shadow strength and makes for a much better lighting option than a single bulb.
Available from good DIY and lighting shops.

 

Tell a Friend

Translate This Page To:

Albanian Arabic Bulgarian Catalan Chinese Croatian
Czech Danish Dutch Estonian Filipino Finnish
French Galician German Greek Hebrew Hindi
Hungarian Indonesian Italian Japanese Korean Latvian
Lithuanian Maltese Norwegian Polish Portuguese Romanian
Russian Serbian Slovak Slovenian Spanish Swedish
Thai Turkish Ukrainian Vietnamese

Powered by: ALS & Google

 Site Visitors >> 


Official Dart Organisations Website Links for Steel-tip and Soft-tip Darts.

Professional Darts Corporation Professional Darts Players Association International Darts Players Association European Darts Union International Dart Federation World Darts Federation England Darts Organisation British Darts Organisation

  


Home

Contact

Site Information

Darts Equipment

Darts501 Mobile

mobile site

Darts Resource Standard Board Games Casino Board Games

Manchester Board Games

Yorkshire Board Games Five's Board Games
Dartboard Setup

Improve Your Game

Checkouts

Site Map


Supporting the major darts manufacturers from around the World

Unicorn Darts Winmau Harrows Bulls Target Master Darts McKicks
Cosmodarts Bottelsen American Dart Lines One80 Shot Datadart


This site uses cookies for tracking viewers visits to learn more about cookies how they are used and how to prevent your visit being recorded click here.
Copyright Darts501.com | All Content & Graphics Copyright all rights reserved. Logos links to their respected owners.

Web design by David King

Darts501.com Home Advertise Here!